- Instruction Manual
- Sor 510-lt-10 User Manual Pdf
- User Manual Pdf
- User Manual For Iphone
- Sor 510-lt-10 User Manual 2017
This is the manuals page for Other. In this page you find schematic, users and instructions manuals, service manuals, technical supplement, leaf leads and other good stuff. In this example, 088-100A-KIT fits a Land Cruiser built between 1963 and 9/73. The ending month/year means this part Fits vehicles up to but not including September 1973 or vehicles built between January 1, 1963 and August 31, 1973.
Form 451 (11.13) ©SOR Inc.
1/8
The SOR
®
1510 Level Switch mounts into the side of a vessel. Electric switching action is
provided by the float moving a magnet into the field of a hermetically sealed reed switch
capsule.
The unit may be mounted for either high or low liquid level alarm by rotating the switch
body to the proper position. The body wrench flats provide for ease of rotation and proper
positioning. See decal on housing.
Before Installation of the Level Switch:
Inspect the unit for any shipment damage.
Check for mechanical clearance of
the float. Float must move freely without binding throughout its stroke.
Use an acceptable thread compound when installing unit to ensure a leak-free fit and to
avoid thread galling.
To achieve required function, install the unit according to the nameplate instructions
shown here.
NOTE: If you suspect that a product is defective, contact the factory or the SOR Representative
in your area for a return authorization number (RMA). This product should only be installed by
trained and competent personnel.
1510
Side Mounted
Level Switch
General Instructions
NC - indicates
circuit is closed
Registered Quality System to ISO 9001
Design and
specifications are
subject to change
without notice.
For latest revision, go to
www.sorinc.com
Table of Contents
Installation ...................................... 3
SIL Installation Instructions .................. 3
Float Attachment ............................... 3
Dimensions ..................................... 4
Electrical Connection .......................... 5
Special Conditions ............................. 5
Wiring for DPDT Relay ........................ 6
ATEX and IECEx Marking Details ............ 6
Declaration of Conformity .................... 7
Troubleshooting ................................ 8
Replacement Parts ............................ 8
rench flats provide for ease of rotation and proper
maage.
THIS SIDE UP
N.C. @ LOW LEVEL
THIS SIDE UP
N.C. @ HIGH LEVEL
THIS SIDE UP
N.C. @ HIGH LEVEL
THIS SIDE UP
N.C. @ LOW LEVEL
Nameplate Position
for Low Level Alarm
Nameplate Position
for High Level Alarm
Form 451 (11.13) ©SOR Inc.
5/8
Special Conditions for Safe Use
The permanently attached leads must be suitably protected against mechanical damage and
terminated in a suitable junction or terminal facility with a minimum degree of protection of
at least IP20.0.
This apparatus may have a combined nameplate which carries multiple approvals
(intrinsically safe and flameproof). The equipment should be marked as to which protection
method it is installed as and shall not be changed or utilized in any other means than was
originally marked by the end user.
Ensure that the wiring conforms to all applicable local and national electrical codes and
install unit(s) according to relevant national and local safety codes.
Instruction Manual
Electrical connection is free wire leads with a 1/2” NPT(F) conduit connection. Use two
wrenches — one to hold the hex conduit connection, the other to tighten conduit fitting.
Switching element is a hermetically sealed reed switch.
Electrical Connection
SPST
Reed Switch
Capsule
SPDT
Reed Switch
Capsule
Common Black Lead
Common Black Lead
Normally Open White Lead
Normally Closed White Lead
Normally Open Blue Lead
Do not exceed
Sor 510-lt-10 User Manual Pdf
catalog stated electrical
ratings. Improper
current input to switch
will cause permanent
damage to contacts.